Description
- Brand: ABB
- Full Model Number: DSCS131
- Ordering Part Number: 57310001-LM
- Lifecycle Status: Legacy spare; current official ABB lifecycle phase requires confirmation
- Core Function: MasterFieldbus communication module for industrial control systems
- System Association: ABB Advant OCS; verify the specific MasterPiece or MP200 configuration
- Top 3 Technical Specs: MasterFieldbus communication interface; control-system bus connectivity; redundancy-related application support, subject to system configuration
- Stock and Condition: Confirmed against current inventory at quotation; request unit-specific condition, identification photographs, and test records
- Shipping: Dispatch date and express-shipping cutoff confirmed before order release
- Warranty: Written coverage and return terms established in the sales quotation
Supply Chain & Technical Deep Dive
When an installed ABB control system depends on a legacy communication module, a hardware failure can interrupt data exchange between controllers and connected equipment. The ABB DSCS131 57310001-LM MasterFieldbus Communication Module is identified in industrial spare-parts catalogs as a communication component associated with ABB Advant OCS equipment. Replacement sourcing should begin with the complete ordering number, the installed hardware revision, and the relevant system documentation. A model-name match alone does not establish interchangeability. For maintenance teams managing older installations, securing a verified spare can reduce procurement delays while preserving the existing control architecture.
The investment case rests on avoiding unnecessary system replacement, engineering work, and extended downtime. A correctly matched DSCS131 may allow a plant to retain its established communication architecture without undertaking a wider migration project. Its applicability to a particular MasterPiece or MP200 installation must be verified against the installed configuration. Do not assume a specific transmission rate, operating voltage, or firmware requirement without an applicable ABB technical document. For total cost of ownership (TCO), compare the replacement cost with the cost of engineering review, commissioning, production interruption, and future spare-parts availability. Legacy components can become harder to source as inventory declines, so procurement planning should include a backup-unit assessment and a longer-term lifecycle review.

Migration, Compatibility & Field Traps
Replacement Matrix
| Classification | DSCS131 Assessment | Engineering Action |
|---|---|---|
| Drop-in Replacement | Conditional | Match the full part number, revision, mounting arrangement, connectors, and installed system configuration. |
| Software Compatible | Requires verification | Check the applicable controller software, firmware dependencies, and communication configuration. Do not assume a firmware update is necessary. |
| Hardware Modification | Not established | Do not modify wiring, connectors, or rack interfaces without an approved technical procedure. |
| Redundant System Compatibility | Configuration-dependent | Verify the applicable redundancy arrangement, module pairing, and system-level configuration before installation. |
Field Traps — Watch Out
- Part Number and Revision Mismatch: Confirm that the installed unit is DSCS131 with ordering number 57310001-LM. Compare its identification label and revision information with the replacement. Similar-looking ABB communication boards may serve different functions or system configurations.
- Bus and Redundancy Configuration: Before removal, document the existing bus connections, module position, redundancy arrangement, and relevant configuration settings. Incorrect reconnection or an incompatible module revision can prevent communication from being restored.
- Power Isolation and ESD: Follow the applicable ABB maintenance procedure for power isolation and module replacement. Use electrostatic discharge protection, and never assume energized insertion or removal is permitted without specific documentation.
Pre-Installation Approval Checklist
The maintenance engineer should confirm the following before authorizing installation:
- The complete part number and applicable hardware revision match the approved replacement.
- The target controller and installed communication architecture support the proposed unit.
- Firmware and configuration requirements have been checked against the applicable documentation.
- The required backup and redundancy arrangements are understood.
- The commissioning and rollback procedures are available before the equipment is taken out of service.

ABB Advant Master -S100 I_O System
Quality Assurance & Testing SOP
The pre-shipment quality process for the ABB DSCS131 57310001-LM should establish product identity, physical condition, and functional status. Each test record should distinguish inspections actually completed from checks that require a compatible ABB system.
OEM Identification and Visual Inspection
Inspect the product label, ordering number, manufacturer markings, serial information where present, connector layout, PCB condition, and visible signs of unauthorized rework. Compare available identification details against applicable OEM references. Visual inspection can identify discrepancies, but it cannot independently establish authenticity.
PCB and Connector Examination
Inspect connector contacts, solder joints, PCB surfaces, mounting points, and accessible components for corrosion, contamination, cracks, mechanical damage, and signs of overheating. Record any exception and exclude units that fail the applicable acceptance criteria.
Electrical and Interconnect Checks
Perform appropriate continuity and interconnect checks using a documented procedure. Confirm that test points and limits apply to this specific board revision. Do not apply arbitrary voltages to unidentified pins or interfaces.
Power-On and Diagnostic Verification
Where an approved, compatible test setup is available, verify startup behavior and the diagnostic indicators documented for the applicable version. Check relevant Power, RUN, ERR, Fault, or communication indications only where those indicators are fitted and documented. Record the actual observed states rather than assuming all variants use identical indicators.
MasterFieldbus Communication Test
Install the board in a compatible test configuration and verify the documented communication path. Check module recognition, communication status, and data exchange with the associated equipment. For a redundancy-capable application, verify the applicable primary and standby behavior only when the test configuration supports it.
System-Level I/O Load Verification
A communication module is not itself a discrete output module. Where the participates in the control path, test end-to-end communication with representative connected I/O equipment and approved test loads. Confirm that relevant signals and status updates pass through the configured system as expected. Record the test arrangement and distinguish communication verification from direct output-load testing.
Final Inspection and Dispatch Release
Release the unit only after its identity, physical condition, and required inspection results have been reviewed. The inspection record should include the following:
- Model and ordering part number
- Visible condition and identification photographs
- Tests completed and their results
- Functional-test configuration and any limitations
- Final acceptance status and applicable warranty documentation
Acceptance Standard: No unit should be represented as functionally tested unless the relevant tests were actually performed and recorded.

ABB Advant Master -S100 I_O System
Procurement-Driven FAQ
Is the ABB 57310001-LM genuinely in stock, and what is the overnight shipping cutoff?
Stock must be confirmed against the current physical inventory for the exact ordering number and requested condition. Dispatch timing depends on order approval, packing, destination, export requirements, and carrier collection schedules. Request written confirmation of stock allocation and the applicable shipping cutoff before committing to a maintenance window.
How do you verify the condition of an obsolete or surplus ?
Request clear photographs of the identification label and connectors, a written condition statement, and available inspection or test records. The quotation should distinguish unused inventory from previously installed or refurbished equipment. If functional testing is available, confirm whether it covers only startup behavior or includes communication testing in a compatible system.
What warranty and return terms apply if the is defective?
The applicable warranty period, return authorization process, notification deadline, and exclusions should be stated in the quotation or sales order. Confirm these terms before purchase. If a fault occurs after installation, retain the product label, inspection records, installation details, and diagnostic evidence to support the investigation.
Will firmware or controller compatibility affect installation?
Potentially. Compatibility depends on the host control system, installed hardware revision, software configuration, and documented communication requirements. Do not assume the module is compatible with newer controller generations solely because it carries the same product designation. Obtain engineering confirmation before commissioning.
What information is required for an accurate quotation?
Provide the complete ordering number 57310001-LM, the required quantity, photographs of the existing module, the installed controller or system identification, the requested condition, and the destination country. Include the required delivery date and any redundancy or commissioning constraints. These details help establish the correct variant, confirm available inventory, and identify compatibility questions before the order is released.


