1. AMAT 0090-02346 | CE/UL Industrial RF Hardware

2. Unboxing & Physical Snapshot

• Model & Brand: AMAT 0090-02346 (Applied Materials)
• Product Type: RF Filter Assembly
• Application: Semiconductor manufacturing equipment RF filtering component. The 0090-02346 part is identified in supplier listings as an Applied Materials RF Filter used with 200mm Producer equipment, with references linking it to assemblies including 0100-00698.
• Approximate Physical Dimensions (W × H × D):
  • Estimated: 120 × 80 × 40 mm
  • Exact dimensions depend on installed RF housing revision.
• Estimated Shipping Weight: Approximately 0.27 kg based on available inventory information.
• What’s in the Box:
  • AMAT 0090-02346 RF Filter assembly
  • RF connector interfaces
  • Mounting hardware (if supplied)
  • Protective anti-static packaging
  • Traceability label / inspection record when available

3. Product Introduction

RF stability is critical inside semiconductor process equipment. The AMAT 0090-02346 functions as an RF filtering component within Applied Materials process tool assemblies, helping control unwanted electrical noise and maintain predictable RF power behavior. The part is associated with 200mm Producer equipment configurations, where process consistency depends on controlled power delivery and clean signal paths.

Treat this component as a precision RF asset. Inspect the connector surfaces, mounting points, housing condition, and identification markings before installation. RF components can appear physically intact while suffering from contamination, damaged shielding, or degraded internal elements (which can affect plasma process stability). Verify the exact tool model and BOM position before replacement.

4. Core Technical Specifications

Parameter	Value
Manufacturer	Applied Materials (AMAT)
Part Number	0090-02346
Component Type	RF Filter
Equipment Application	Semiconductor process equipment
Associated Tool Family	200mm Producer (reference)
Assembly Reference	Related to 0100-00698 assembly configurations
RF Function	Noise filtering / RF signal conditioning
Operating Frequency	Tool configuration dependent
RF Power Rating	Verify OEM equipment specification
Connector Type	RF interface, revision dependent
Housing Material	Industrial metal enclosure (typical)
Processor	None
Memory	None
Firmware	None
Power Consumption	Passive component
Heat Dissipation	Generated from RF losses only
Cooling Method	Equipment airflow dependent
Mounting Method	Tool chassis installation
Storage Requirement	Controlled dry electronics storage

AMAT 0090-02346

5. Global Compliance & Industry Certifications

Expected compliance considerations for the AMAT 0090-02346 include:

• CE Mark consideration when installed within an approved Applied Materials semiconductor equipment system.
• UL/cUL Listed or Recognized components may apply depending on the complete equipment assembly.
• RoHS / REACH compliance documentation may be required for semiconductor manufacturing supply chains.
• IEC electrical safety considerations apply through the finished equipment installation.
• ATEX/IECEx is generally not expected unless the complete process tool is installed in a classified hazardous area.
• Marine approvals such as DNV GL are generally not applicable for standard fab equipment.

RF components require controlled electrical characteristics because unexpected signal loss, leakage, or interference can affect process equipment performance and may trigger equipment alarms.

Verify specific lot certifications with OEM.

6. Long-Term Storage & Asset Preservation Guide

• Keep the AMAT 0090-02346 inside its original ESD protective packaging. Seal RF connectors with protective caps when available.
• Maintain warehouse humidity below 60% RH to reduce oxidation risk on RF contacts and metal mounting surfaces.
• Store away from corrosive chemicals, cleanroom exhaust areas, and temperature cycling zones.

Inspect connector surfaces before installation. RF contact degradation can create high-frequency performance issues that are not visible during basic inspection.

Avoid stacking heavy components on the filter housing. Mechanical deformation can affect RF alignment.

7. Physical Installation Prerequisites

• Install only in the approved Applied Materials equipment configuration.
• Confirm RF input/output orientation before connection.
• Inspect RF connectors for contamination, scratches, or damaged threads.
• Tighten mounting hardware according to equipment maintenance procedures.
• Maintain proper chassis grounding.
• Keep RF cabling separated from unrelated power wiring where required.
• Ensure equipment cooling airflow paths remain unobstructed.
• Leave approximately 50 mm clearance around ventilation areas where the tool design permits.
• Use proper ESD handling procedures during installation.

8. Buyer’s FAQ (Logistics & Compliance Focus)

Q: What HS Tariff Code is commonly reviewed for the AMAT 0090-02346?
A: RF filter assemblies are commonly evaluated under HS 8548 or related electrical component classifications, depending on construction and declared function. Final classification should be confirmed with the destination customs authority.

Q: Why does Country of Origin (COO) documentation matter for this AMAT part?
A: COO records support customs clearance, semiconductor equipment supplier audits, and maintenance traceability. Match COO information with the commercial invoice, packing list, and part identification label.

Q: Is shipping insurance recommended for the 0090-02346 RF Filter?
A: Yes. Although the component is lightweight, RF assemblies are precision parts where connector damage or contamination can affect performance. Use protective packaging and declared-value shipping coverage.

Q: Does the AMAT 0090-02346 include firmware pre-loaded?
A: No. This is a passive RF filter assembly and contains no processor, memory, or firmware. Configuration is managed by the Applied Materials equipment control system.